No. | Brand | s | H | A | L | B | D | U | d |
5753 | iso | - | - | - | - | 23.8 mm | - | - | 30 mm |
12240 | iso | - | - | - | - | - | - | 13 mm | - |
281 | iso | 25.4 mm | - | 58.737 mm | 136.525 mm | - | - | - | - |
16281 | iso | - | - | - | - | - | - | - | - |
15243 | iso | - | 192.484 mm | - | 349.25 mm | - | - | - | - |
din 281 | iso | - | - | - | - | 23 mm | 120 mm | - | 65 mm |
492 | iso | - | - | - | - | 46 mm | 130 mm | - | 60 mm |
ya100rr | timken | - | - | - | - | 4.5938 in | 3.6250 in | - | 1.2500 in |
15 | iso | - | - | - | - | - | - | - | - |
din 12240 | iso | - | - | - | - | 36.50 mm | 90.0000 mm | - | 40.000 mm |
iso 5753 bearing | d:30 mm; Pu:1.232 kN; ra:1 max; Weight:0.31 kg; B:23.8 mm; Oil:8 400 min-1; Bearing designation:3206 ; a:41 mm; Static (Cor):27.100 kN; Dynamic (Cr):30.998 kN; |
iso 16281 bearing | Category:Bearings; Inventory:0.0; Minimum Buy Quantity:N/A; Weight:0.05; Product Group:B00308; |
iso 12240 bearing | Mass needle roller and cage assembly:0.0023 kg; Basic static load rating C0:8.65 kN; Fatigue load limit Pu:0.98 kN; Ew:15 mm; Limiting speed:30000 r/min; Reference speed:26000 r/min; Fw:12 mm; U:13 mm; Basic dynamic load rating C:6.16 kN; |
iso 281 bearing | Basic dynamic load rating C:77 kN; a:3.969 mm; s:25.4 mm; d2:68.659 mm; A:58.737 mm; L:136.525 mm; A1:76.994 mm; Limiting speed:4500 r/min; A5:29.369 mm; A6:19.05 mm; |
iso din 12240 bearing | Sealed Speed Rating n3:5000 rpm; Grease Speed Rating n1:5000 rpm; Accessories:Shield & Seal; Oil Speed Rating n2:6700 rpm; Fillet Radius ra:1.50 mm; Basic Dynamic Radial Load Rating C:60500 N; D:90.0000 mm; d:40.000 mm; Basic Static Radial Load Rating Co:43000 N; B:36.50 mm; |
iso 15243 bearing | H1:101.6 mm; H:192.484 mm; RG:3/8 NPT; Max. speed for Taconite seal:750 r/min; R2:27.781 mm; ba:40.481 mm; End plug (suffix Y):EPR 11; Taconite seal (db shaft position):TER 112; Mass pillow block:21.2 kg; L:349.25 mm; |
iso din 281 bearing | B:23 mm; da:72 min; Pu:1.819 kN; Grease:5 300 min-1; Oil:6 300 min-1; Weight:0.997 kg; rs:1.5 mm; d:65 mm; Static (Cor):40.011 kN; D:120 mm; |
iso 15 bearing | Ca:107.798 mm; PosiTrac Plus contact element (db shaft position):B10724-175; P90°:334 kN; Initial grease fill:2154.6 g; db:222.25 mm; A2:295.275 mm; Lock nut:AN 40; Eye bolt:2 x 3/8-16 UNC; RG:1 NPT; da:200 mm; |
timken ya100rr bearing | locking device:Set Screw; D:3.6250 in; bore type:Round; mounting type:Four-Bolt Flange; manufacturer upc number:4547359791129; B:4.5938 in; d:1.2500 in; |
iso 492 bearing Video
ISO 492:2002 - Rolling bearings — Radial bearings ... - ISO
ISO 492 specifies tolerances for boundary dimensions (except chamfer dimensions) and the running accuracy of radial rolling bearings specified in ISO 15, ISO
Bearing Tolerances and Precision Levels | AST Bearings
In almost all cases, these standards are similar to or state equivalency with ISO 492. The table below shows the equivalent tolerance grades for three of the most
ISO 492 - SiS
STANDARD. ISO. 492. Fourth edition. 2002-04-15. Rolling bearings — Radial bearings —. Tolerances. Roulements — Roulements radiaux — Tolérances
Bearing Tolerances - NTN Global
running accuracy, are regulated by ISO and JIS B 1514 standards .... Notes 1: JIS B 1514, ISO 492 and 199, and DIN 620 have the same specification level
ISO 492:2002(en), Rolling bearings — Radial bearings
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible
ISO 492:2014 - Rolling bearings -- Radial bearings ... - ISO
ISO 492:2014 specifies dimensional and geometrical characteristics, limit deviations from nominal values, and tolerance values to define the interface (except
Tolerances
Tolerance classes and the corresponding values for certain tolerance characteristics are specified in ISO 492 (for radial bearings) and ISO 199 (for thrust
ISO 492:2014(en), Rolling bearings — Radial bearings
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the